Sunbird

all messages by user

1/27/2016
Topic:
Tajima 15 Learning Curve

Sunbird
Sunbird
Mike Harper
Try not to use more than 6-8 charactors in the name of the file. See if that will pork. Remember, floppy disks are good with short naming files
JJ
1/27/2016
Topic:
Run Stitch Unreal

Sunbird
Sunbird
I have come up with a trick to do a run stitch around a design without one jump, or trim or going over any line more than twice. I fact, I cover the whole run in 2 runs without backup or overlapping any run stitch more than twice. No cleaning of jump stitches after run is done.
3/31/2021
Topic:
New Fonts

Sunbird
Sunbird
Good day
Pulse Signature v.16. Maestro -Beta 16.1.3.7295. Windows 10 Pro
Two fonts: Varsity & Varsity New looks different from each other in the preview pane when you select one of the two fonts while going through the fonts before you apply it. But they are the same on the sceen after you have selected them. See attachment
Thanks
12/22/2022
Topic:
Steil error

Sunbird
Sunbird
It is not an error or a problem in Pulse. It is a setting in your PROPERTIES.
1. Select the segment.
2. Select SEGMENT SETTINGS and go to CONNECTIONS on the left.
3. On the right, tick TRIM AT: and make the trim distance 20mm.

The program is looking for a place to trim, and because the steil is placing the start and stop in the same spot, is because there he has
no TRIM AT: command. I use 20mm, you can use any value in there, depending ho far you want the machine to jump between segments before trimming while the machine is using the same color thread.

OomJayJAy
12/22/2022
Topic:
Steil error

Sunbird
Sunbird
Hi. Have send you a private message.

TARA Design wrote:
The problem here is the steil it self not the TRIM or the JUMP. If you see my sample in my attached file you can see that I set my beads in different possition but still the starting is in the ending point.
12/22/2022
Topic:
Changing "Close a Segment" Shortcut?

Sunbird
Sunbird
Hi DJ
I use Pulse 16. The closing a segment is set under a different place. Maybe it is the same for your digitizing program.
Have a look under: TOOLS - User Settings - Environment - Shortcuts. There you use either Classic or Standard shortcuts.
I hope this helps.
OomJayJay
12/31/2022
Topic:
Steil stitches

Sunbird
Sunbird
Hi D
Can you share the steil stitch file with me? I would like to help you.
OomJayJay
1/24/2023
Topic:
Steil stitches

Sunbird
Sunbird
DancingBay
I have corrected your steil for you. And posted the cause why the steil did not work. I have also attached the file so you can see it does work. Just a few minor adjustments to digitizing style and nodes. And it works.
2/1/2023
Topic:
problem to open old files

Sunbird
Sunbird
Morning
Please send me one of the files that you are unable to open.
Thanks
JayJay
6/28/2023
Topic:
Exporting Image

Sunbird
Sunbird
Hi Jose
This is an easy solution.
1. Select the whole design.
2. Select the designs properties
3. Go to "Connections" in the segment settings.
4. Make sure the "Trim at:" is ticked.
5. In the block below "Trim at:" put the value to 1mm
6. Click apply and see if the jump stitches are gone.
7. Export the design as a image, and you will see there is no jump stitches.
8. Remember to click "Undo" after you have exported the design in order to put the "Trim at:" back to its original setting.

I hope this helps.
OomJayJay
6/28/2023
Topic:
Long Tails

Sunbird
Sunbird
Hi
The reason why you have long tails, is because the picker stays in the forward position to long while the machine is preparing to trim the thread. Tara is correct, you need to find the setting on your machine that controls the amount of time the picker stays in the forward position before it moves out again.
Good luck
OomJayJay
1




Powered by Jitbit Forum 8.3.7.0 © 2006-2013 Jitbit Software